Bryant 619FNQ Manual de instalación

Cancels: New II 619F-18-14/1/06installation, start-up andservice instructionsIN-CEILING CASSETTEFAN COIL UNITS619FNF619FNQSizes 018-03036CONTENTSPageS

—10—IV. STEP 4 — COMPLETE REFRIGERANT PIPINGCONNECTIONSIMPORTANT: During unit installation make the refrigerantconnections first and then the electric

—11—V. STEP 5 — MAKE ELECTRICAL CONNECTIONS See Tables 6A and 6B for electrical information.A. Units With Electric HeaterThe unit is equipped with tw

—12—Room ControllerConnectionsGroundConnectionOutdoor UnitConnectionsLowVoltageHighVoltagePowerConnectionsFig. 21 — 619FNF Unit Matched to 538ENF Outd

—13—LowVoltageHighVoltageRoom ControllerConnectionsOutdoor UnitConnectionsPowerConnectionsGroundConnectionFig. 22 — 619FNQ Unit Matched to 538ENF Outd

—14—LowVoltageHighVoltageRoom ControllerConnectionsGroundConnectionOutdoor UnitConnectionsPowerConnectionsFig. 23 — 619FNQ Unit Matched to 538QNF Outd

—15—ETTESSAC LABOLG 619FNFRESNEDNOC ROODTUO 538ENFNOTE 6NOTE 5NOTE 4YALPSIDRIA-MTLIOC-MT"D" RALUDOMBCP1 LORTNOCREPPOC ERABTCENNOCSID TINU OT

—16—ETTESSAC LABOLG QNF619RESNEDNOC ROODTUO FNE538NOTE 6NOTE 5YALPSIDRIA-MT LIOC-MT"D" RALUDOMBCP1 LORTNOCREPPOC ERABTCENNOCSID TINU O

—17—ETTESSAC LABOLG 619FNQRESNEDNOC ROODTUO 538QNFNOTE 6NOTE 5YALPSIDRIA-MT LIOC-MT"D" RALUDOMBCP1 LORTNOCREPPOC ERABTCENNOCSID TINU O

—18—INTERNAL CONTROL PANEL619FNF018CapacitorGMC boardElectric heater board(only on models with electric heater)TransformerHoles for fixing panel in po

—19—C. Wiring the Room ControllerThe room controller is capable of controlling from 1 to 6 fancoil units. The total run length of the wire connecting

—2—INSTALLATIONI. STEP 1 — COMPLETE PRE-INSTALLATION CHECKSA. Unpack Unit (See Fig. 1)Move the unit to final location. The grille panel and theremote

—20—4.72”(120)ØA BØA Ø CDuct connection flangeClip1/4" (6 mm) neoprene gasketInsulated flexible ductFresh air intakeConditioned air supply to an

—21—III. ROOM CONTROLLER CONFIGURATION SETUPTo configure the room controller, press the Mode button for5 seconds. After 5 seconds, “10” will appear. T

—22—Table 8 — Modular Platform D Unit Configuration ValuesOnly the current value being displayed is transmitted. Oncethe Fan button is pressed, the ro

—23—4. Ensure that the filters and return air grilles havebeen installed and that the discharge louvers arecorrectly positioned.SERVICE AND MAINTENANC

Copyright 2006 Bryant Heating & Cooling Systems Printed in U.S.A. CATALOG NO. 02-619F0001-IIGreenLEDRed LEDYellow LEDRemote controlsignal receiver

—3—2'-4-11/32"(720)1'-9-21/32"(550))515("23/98-'11-7/8"(47)1'-11-7/16"(595))318("8-'2)069("

—4—Table 4A — 619FNF Physical Data LEGEND*See Table 3 for factory charge and additional field charge requirements.SYSTEM SIZE 018

—5—Table 4B — 619FNQ Physical Data LEGEND*See Table 3 for factory charge and additional field charge requirements.SYSTEM SIZ

—6—II. STEP 2 — LOCATING AND MOUNTING THE UNITA. Locating the UnitInstall the unit as centrally as possible in the room. The air-flow direction can be

—7—The condensate may be discharged at a maximum height of77/8 in. above the unit, as long as the ascending tube is verti-cal and aligned with the dra

—8—III. STEP 3 — LOCATING AND MOUNTING THE ROOMCONTROLLERA. Locating the Room ControllerSee Fig. 14 for room controller dimensions. If the air sensori

—9—B. Mounting the Room Controller (Fig. 15-17)Unscrew the side fixing screw. Open the room controller rearmounting base to expose the mounting holes.